Securing a Child Restraint Designed forthe LATCH System

CAUTION:
If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual.

CAUTION:
Each top tether anchor and lower anchor in the vehicle is designed to hold only one child restraint. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash.
A child or others could be injured if this happens. To help prevent injury to people and damage to your vehicle, attach only one child restraint per anchor.

CAUTION:
Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Secure any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Be sure to follow the instructions of the child restraint manufacturer.

Notice: Contact between the child restraint or the LATCH attachment parts and the vehicle’s safety belt assembly may cause damage to these parts. Make sure when securing unused safety belts behind the child restraint that there is no contact between the child restraint or the LATCH attachment parts and the vehicle’s safety belt assembly.
Folding an empty rear seat with the safety belts secured may cause damage to the safety belt or the seat. When removing the child restraint, always remember to return the safety belts to their normal, stowed position before folding the rear seat.

1. Attach and tighten the lower attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to your child restraint manufacturer instructions and the instructions in this manual.

1.1. Find the lower anchors for the desired seating position.
1.2. Pull the strap at the center of the seat where the seat cushion meets the seatback. This will allow you to fold the seat cushion up and out of the way.

Lift the flap to expose the anchors and then lower the seat cushion. See Rear Seat Operation on page 16 for additional information. Be sure the cushion is locked into place.

1.3. Put the child restraint on the seat.
1.4. Attach and tighten the lower attachments on the child restraint to the lower anchors.

2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if your vehicle has one. Refer to the child restraint instructions and the following steps:
2.1. Find the top tether anchor.
2.2. Route and tighten the top tether according to your child restraint instructions and the following instructions. If your vehicle has a cargo shade, route the top tether between the seatback and the cargo shade.

Fold down the head

Fold down the head restraint and route the single tether under the head restraint and in between the head restraint posts.

Fold down the head

Fold down the head restraint and route the dual tether around the head restraint.

3. Push and pull the child restraint in different directions to be sure it is secure.

    See also:

    Starting the Vehicle
    1. Aim the RKE transmitter at the vehicle. 2. Press . 3. Immediately after completing Step 2, press and hold until the turn signal lamps flash. When the vehicle starts, the parking lamps w ...

    Heated and Ventilated Seats
    On vehicles with heated and ventilated seats, the controls are located on the front doors and the ignition must be on to use the feature. : Press to heat the seat and seatback. : Press to he ...

    Removing the Spare Tire and Tools
    To access the spare tire and tools: 1. Open the trunk. 2. Remove the spare tire cover. 3. Turn the retainer nut counterclockwise and remove the spare tire. Place the spare tire next to the tire ...